Clausing BPS1 Mill Specifications
Table & Ways
Travels Table Size 9” x 49”
Table Height Above Floor (max) 47.25”
Table Load 750lbs.
No. of T-slots 3
T-slot Width 5/8”
T-slot Center Distance 2.5”
Table Ways Dovetail
Knee Ways Dovetail
Column Ways
X Longitudinal Table (w/o pwr feed) Dovetail
36”
X Longitudinal Table (w/pwr feed) 33”
Y Cross 12”
Knee 16”
Ram 12”
Throat Distance (min) 6.75”
Throat Distance (max) 18.75”
Table to Nose Gauge Line (min/max) 2.5” / 18.25”
Motors & Spindle Spindle Motor (duty cycle/continuous) 3 Hp / 2Hp
Amp. Draw 208v. 7
Amp. Draw 230v. 7
Amp. Draw 460v. 5
Speed Range High Range 500-4200 RPM
Speed Range Low Range 60-500 RPM
Main Spindle Taper R8
Spindle Travel 5”
Quill Feed (in/rev.) .0015/.003/.006
Quill Diameter 3.375”
Capacities Power Quill Feed 3/8”
Milling Capacity (mild steel) 2 CI/in
Boring Range (mild steel) 6” dia
Spindle Diameter 1.875”
Feed Rate Range (X,Y) 0.50-35 ipm
Minimum Increment 0.001”
Construction
& Weight Floor Area 7 x 10 ft
Height 87”
Net Weight 1930 lbs
Shipping Weight 2075 lbs
Input Power 208/230/460 Volt
3 Phase, 50/60 hz
4KVA
Standard Equipment
· Mechanical Variable Speed Drive System
· Patented 2J Head gives unique air cooling for spindle bearings
· Hardened & Scraped, X, Y & Z Ways
· Scraped gibs for alignment
· T-slots are ground to provide reference edge for positioning your workplace
· Hardened & Scraped Table Surface
· Hardened & Ground Spindle
· Chrome-Plated Ways and Gibs
· Chromed & Ground Quill
· Chromed X, Y, & Z Leadscrews
· Double Nut Leadscrew for backlash compensation
· ABEC 7/CP4 Spindle Bearings
· One-piece way wipers
· 7/16”-20 Imperial Drawbar R8
· 3 / 2 Hp AC Motor (3Hp 30 minute duty/ 2Hp continuous)
· Articulating Head for Compound Angles
· Worm gear angular positioning of head in two directions
· Lever-operated manual rapid quill movement
· Handwheel for fine quill feed
· Adjustable automatic feed disengagement for quill feed in both directions
· Micrometer depth stop
· Reversing switch for clockwise or counter clockwise operation
· R8 Spindle taper
· Spindle Brake (Hand operated)
· One-shot lubrication
· Leveling bolts and pads (in tool box)
· Tool Kit, Test and Accuracy Chart
· Operations Manual/Parts List
· Series 1 Standard 208/230 or 460 3 Phase (other voltages require a transformer)
Investment
Clausing BPS1 w/Mechanical Sheave Pulley Drive
BPS1R08 VS Mill, 9” x 49” Table, R8 Spindle, 3 Hp $ 21,800.00
BPS1R08C VS Mill, 9” x 49” Table, R8 Spindle, 3 Hp 22,455.00
Coolant System in Base and On/Off Switch
BPS1QC30 VS Mill, 9” x 49” Table, NMTB 30 Quick Change SPDL, $ 22,350.00
3 Hp
BPS1QC30C VS Mill, 9” x 49” Table, NMTB 30 Quick Change SPDL, 23,000.00
3 Hp, Coolant System in Base and On/Off Switch
Bridgeport Specific Accessories
BPS031 Right Angle Attachment R8 (only no support or arbor) $ 2,250.00
(NOT FOR QUICK CHANGE SPINDLE)
BPS8408 Air Power Draw Bar R8 (US MFG) 1,195.00
Drawbar Installation $ 200.00 NET
BPS100 Spindle chip guard 785.00
BPS001 Coolant Chip Pan 585.00
BPS040 4” Column Riser Block Series 1 650.00
BPS041 6” Column Riser Block Series 1 700.00
BPS042 8” Column Riser Block Series 1 755.00
BPS050 Front Accordion & Rear Flat Cover Y-Axis 240.00
BPSX350 X-Axis Servo Feed (USA MFG) 1,880.00
Power Feed Installation $ 175.00 NET
BPSY350 Y Axis Servo Feed (USA MFG) 2,000.00
Power Feed Installation $ 175.00 NET
BPSK350 Knee Servo Feed (USA MFG) 1,985.00
Power Feed Installation $ 175.00 NET
BPS200 Accu-Lube System 2,365.00
BPS2VRSP Series 1 2 Year Spare Parts 1.5Hp 450.00
Special Electrics
BPS-NFPA79-SM NFPA Special Electrics Knee Mill $ 9,575.00
BPS8408-NFPA Air Power Drawbar R8 (w/110V Solenoid for air) 1,330.00
(requires BPS-NFPA79-SM)
BPS200-NFPA Accu-Lube System w/NFPA 2,540.00
(requires BPS-NFPA79-SM)
BPSWOL-NFPA Worklight with Twist Lock Plug 580.00
(requires BPS-NFPA79-SM)
DRO Kits
AR13-35-200M 2 Axis 9”x 49” TBL Acu-Rite 200 DRO $ 2,930.00
AR13-35-300M 2 Axis 9”x49” TBL Acu-Rite 300 DRO 3,300.00
AR4-13-35-200M 3 Axis w/Spindle 9”x 49” TBL Acu-Rite 200 DRO 3,630.00
AR4-13-35-300M 3 Axis w/Spindle 9”x 49” TBL Acu-Rite 300 DRO 4,000.00
AR13-35-16200M 3 Axis w/Knee 9”x 49” TBL Acu-Rite 200 DRO 3,890.00
AR13-35-16300M 3 Axis w/Knee 9”x 49” TBL Acu-Rite 300 DRO 4,260.00
AR4-13-38-16300M 4 Axis w/Knee 9”x 49” TBL Acu-Rite 300 DRO 5,050.00
NW12-36NMS800 2 Axis 9”x 49” Newall NMS800 DRO $ 2,930.00
NW4-12-36NMS800 3 Axis w/Spindle 9”x 49” Newall NMS800 DRO 3,630.00
NW16-12-36NMS800 3 Axis w/Knee 9”x 49” Newall NMS800 DRO 3,890.00
NOTE: Acu-Rite edge finder requires 300 DRO kits
DRO 2 Axis Installation $ 350.00 NET
DRO 3 Axis Installation $ 500.00 NET
DRO 4 Axis Installation $ 650.00 NET
General Accessories
2VS020-1 R8 Milling Chuck Kit w/11 ER Collets $ 565.00
Z384-SET-1 R8 Metric Set 2mm by 1mm, 19 Collets 425.00
Z384-SET-5 R8 Inch Collet Set 1/8 to 7/8 by 32nds, 25 Collets 1,475.00
Z384-SET-6 R8 Inch Collet Set 1/8 to 7/8 by 1/16ths, 13 Collets 315.00
Z384-SET-7 R8 Inch Collet Set 1/8 to ¾ by 1/8ths, 6 Collets 230.00
FV-9031G R8 to J2 Arbor for FV-9030G 170.00
FV-9033G R8 to J6 Arbor for FV-9032G 170.00
FV-9041G 12pc. R8 Collet Rack 60.00
FV-9050G ½” R8 Shell Mill Holder 100.00
FV-9051G ¾” R8 Shell Mill Holder 150.00
FV-9052G 1” R8 Shell Mill Holder 100.00
FV-9080G R8 End Mill Adapter Set 3/16-1 ¼ (8 pcs.) 320.00
2VS002A Central 110v Wiring Point w/6 Plugs & 8’ Power Cord 265.00
2VS010 52 Piece Clamping Kit 195.00
FV-9010G Kurt 6” Vise Only
Clausing BPS1 Mill Specifications
Table & Ways
Travels Table Size 9” x 49”
Table Height Above Floor (max) 47.25”
Table Load 750lbs.
No. of T-slots 3
T-slot Width 5/8”
T-slot Center Distance 2.5”
Table Ways Dovetail
Knee Ways Dovetail
Column Ways
X Longitudinal Table (w/o pwr feed) Dovetail
36”
X Longitudinal Table (w/pwr feed) 33”
Y Cross 12”
Knee 16”
Ram 12”
Throat Distance (min) 6.75”
Throat Distance (max) 18.75”
Table to Nose Gauge Line (min/max) 2.5” / 18.25”
Motors & Spindle Spindle Motor (duty cycle/continuous) 3 Hp / 2Hp
Amp. Draw 208v. 7
Amp. Draw 230v. 7
Amp. Draw 460v. 5
Speed Range High Range 500-4200 RPM
Speed Range Low Range 60-500 RPM
Main Spindle Taper R8
Spindle Travel 5”
Quill Feed (in/rev.) .0015/.003/.006
Quill Diameter 3.375”
Capacities Power Quill Feed 3/8”
Milling Capacity (mild steel) 2 CI/in
Boring Range (mild steel) 6” dia
Spindle Diameter 1.875”
Feed Rate Range (X,Y) 0.50-35 ipm
Minimum Increment 0.001”
Construction
& Weight Floor Area 7 x 10 ft
Height 87”
Net Weight 1930 lbs
Shipping Weight 2075 lbs
Input Power 208/230/460 Volt
3 Phase, 50/60 hz
4KVA
Standard Equipment
· Mechanical Variable Speed Drive System
· Patented 2J Head gives unique air cooling for spindle bearings
· Hardened & Scraped, X, Y & Z Ways
· Scraped gibs for alignment
· T-slots are ground to provide reference edge for positioning your workplace
· Hardened & Scraped Table Surface
· Hardened & Ground Spindle
· Chrome-Plated Ways and Gibs
· Chromed & Ground Quill
· Chromed X, Y, & Z Leadscrews
· Double Nut Leadscrew for backlash compensation
· ABEC 7/CP4 Spindle Bearings
· One-piece way wipers
· 7/16”-20 Imperial Drawbar R8
· 3 / 2 Hp AC Motor (3Hp 30 minute duty/ 2Hp continuous)
· Articulating Head for Compound Angles
· Worm gear angular positioning of head in two directions
· Lever-operated manual rapid quill movement
· Handwheel for fine quill feed
· Adjustable automatic feed disengagement for quill feed in both directions
· Micrometer depth stop
· Reversing switch for clockwise or counter clockwise operation
· R8 Spindle taper
· Spindle Brake (Hand operated)
· One-shot lubrication
· Leveling bolts and pads (in tool box)
· Tool Kit, Test and Accuracy Chart
· Operations Manual/Parts List
· Series 1 Standard 208/230 or 460 3 Phase (other voltages require a transformer)
Investment
Clausing BPS1 w/Mechanical Sheave Pulley Drive
BPS1R08 VS Mill, 9” x 49” Table, R8 Spindle, 3 Hp $ 21,800.00
BPS1R08C VS Mill, 9” x 49” Table, R8 Spindle, 3 Hp 22,455.00
Coolant System in Base and On/Off Switch
BPS1QC30 VS Mill, 9” x 49” Table, NMTB 30 Quick Change SPDL, $ 22,350.00
3 Hp
BPS1QC30C VS Mill, 9” x 49” Table, NMTB 30 Quick Change SPDL, 23,000.00
3 Hp, Coolant System in Base and On/Off Switch
Bridgeport Specific Accessories
BPS031 Right Angle Attachment R8 (only no support or arbor) $ 2,250.00
(NOT FOR QUICK CHANGE SPINDLE)
BPS8408 Air Power Draw Bar R8 (US MFG) 1,195.00
Drawbar Installation $ 200.00 NET
BPS100 Spindle chip guard 785.00
BPS001 Coolant Chip Pan 585.00
BPS040 4” Column Riser Block Series 1 650.00
BPS041 6” Column Riser Block Series 1 700.00
BPS042 8” Column Riser Block Series 1 755.00
BPS050 Front Accordion & Rear Flat Cover Y-Axis 240.00
BPSX350 X-Axis Servo Feed (USA MFG) 1,880.00
Power Feed Installation $ 175.00 NET
BPSY350 Y Axis Servo Feed (USA MFG) 2,000.00
Power Feed Installation $ 175.00 NET
BPSK350 Knee Servo Feed (USA MFG) 1,985.00
Power Feed Installation $ 175.00 NET
BPS200 Accu-Lube System 2,365.00
BPS2VRSP Series 1 2 Year Spare Parts 1.5Hp 450.00
Special Electrics
BPS-NFPA79-SM NFPA Special Electrics Knee Mill $ 9,575.00
BPS8408-NFPA Air Power Drawbar R8 (w/110V Solenoid for air) 1,330.00
(requires BPS-NFPA79-SM)
BPS200-NFPA Accu-Lube System w/NFPA 2,540.00
(requires BPS-NFPA79-SM)
BPSWOL-NFPA Worklight with Twist Lock Plug 580.00
(requires BPS-NFPA79-SM)
DRO Kits
AR13-35-200M 2 Axis 9”x 49” TBL Acu-Rite 200 DRO $ 2,930.00
AR13-35-300M 2 Axis 9”x49” TBL Acu-Rite 300 DRO 3,300.00
AR4-13-35-200M 3 Axis w/Spindle 9”x 49” TBL Acu-Rite 200 DRO 3,630.00
AR4-13-35-300M 3 Axis w/Spindle 9”x 49” TBL Acu-Rite 300 DRO 4,000.00
AR13-35-16200M 3 Axis w/Knee 9”x 49” TBL Acu-Rite 200 DRO 3,890.00
AR13-35-16300M 3 Axis w/Knee 9”x 49” TBL Acu-Rite 300 DRO 4,260.00
AR4-13-38-16300M 4 Axis w/Knee 9”x 49” TBL Acu-Rite 300 DRO 5,050.00
NW12-36NMS800 2 Axis 9”x 49” Newall NMS800 DRO $ 2,930.00
NW4-12-36NMS800 3 Axis w/Spindle 9”x 49” Newall NMS800 DRO 3,630.00
NW16-12-36NMS800 3 Axis w/Knee 9”x 49” Newall NMS800 DRO 3,890.00
NOTE: Acu-Rite edge finder requires 300 DRO kits
DRO 2 Axis Installation $ 350.00 NET
DRO 3 Axis Installation $ 500.00 NET
DRO 4 Axis Installation $ 650.00 NET
General Accessories
2VS020-1 R8 Milling Chuck Kit w/11 ER Collets $ 565.00
Z384-SET-1 R8 Metric Set 2mm by 1mm, 19 Collets 425.00
Z384-SET-5 R8 Inch Collet Set 1/8 to 7/8 by 32nds, 25 Collets 1,475.00
Z384-SET-6 R8 Inch Collet Set 1/8 to 7/8 by 1/16ths, 13 Collets 315.00
Z384-SET-7 R8 Inch Collet Set 1/8 to ¾ by 1/8ths, 6 Collets 230.00
FV-9031G R8 to J2 Arbor for FV-9030G 170.00
FV-9033G R8 to J6 Arbor for FV-9032G 170.00
FV-9041G 12pc. R8 Collet Rack 60.00
FV-9050G ½” R8 Shell Mill Holder 100.00
FV-9051G ¾” R8 Shell Mill Holder 150.00
FV-9052G 1” R8 Shell Mill Holder 100.00
FV-9080G R8 End Mill Adapter Set 3/16-1 ¼ (8 pcs.) 320.00
2VS002A Central 110v Wiring Point w/6 Plugs & 8’ Power Cord 265.00
2VS010 52 Piece Clamping Kit 195.00
FV-9010G Kurt 6” Vise Only 1,025.00
FV-9011G Kurt 6” Swivel Base for FV-9010G 730.00
FV-9012G Vise Step Key Kit 11/16 x 5/8 (set of 2) 95.00
FV-9030G ½” Keyless Drill Chuck 230.00
FV-9032G 1/8” to 5/8” Keyless Drill Chuck 240.00
FV-9070L LED Work Light w/3Pin 110V Plug 190.00
CS-9062 Coolant Mist System 1 Gal 1,425.00
1,025.00
FV-9011G Kurt 6” Swivel Base for FV-9010G 730.00
FV-9012G Vise Step Key Kit 11/16 x 5/8 (set of 2) 95.00
FV-9030G ½” Keyless Drill Chuck 230.00
FV-9032G 1/8” to 5/8” Keyless Drill Chuck 240.00
FV-9070L LED Work Light w/3Pin 110V Plug 190.00
CS-9062 Coolant Mist System 1 Gal 1,425.00
Our knowledgeable staff will assist you with all of you questions.
Contact Us
1287 W Ave.
Ames, IA 50014
Toll Free: 800-237-6330
Office: 515-233-6330
Fax: 515-232-9411
Used Machinery
New Machinery
Precision Rigging
Precision Finishing
SMC Auctions
About Us
Contact Us
© 2025 Smith Machinery Company, Inc.
